Homepage | Set Home | Add to Favorites

Taizhou Huangyan Yuesen Plastic Mould Co.,Ltd

  • No Category

Friends links
  • No link

plastic bottle cap mould,plastic cap injection mould
Click image to view full size image
Product: Views:101plastic bottle cap mould,plastic cap injection mould 
Unit price: Negotiable
Delivery date: Since the payment date Days delivery
Valid until: Long-term effective
Last updated: 2017-11-17 22:17

Mould name:Cap Mould Shaping Mode:Injection Mould

Cap Mold, Cap Moulds, Cap Moulding, cap molding, Cap injection mold

Cap mold design steps

1. Cap mold for the design feasibility analysis, computer chassis, for example, the first component of each product drawings use design software for analysis group legislature that we work in said sets of plans to ensure proper before the mold design drawings for each product sex, on the other hand can be familiar with the importance of each component in the entire chassis to determine the size of the focus, so that in the mold design is very good, specific sets of plans do not detail the methods herein described.

2. Work cap mold after the analysis to be performed in, the product was analyzed what kind of mold structure and mold cap discharge step, each step to determine the content punch work, and expand the use of design software products, expand the product copy and then ships from the follow-up project to start forward, such as a requirement of five product process is completed at the time of stamping expand begin to four projects, three projects, two projects, a project from the drawings, and launched a graphic after expand the work carried out before a project, to complete five projects expand work and meticulous work, note that this step is very important, and need special care, which is good in one step, saving the drawing die in FIG. a lot of time for each project to determine the contents of the press after a good, including molding, the material thickness and outside the line of products retained to determine when the punch and die size for product expansion method will not be described here, will expand the specific method described.

3. Preparation, preparation by Expand diagram, determine the size of the template in the drawing, including the fixed plate, stripper plate, punch, inserts, etc., pay attention to the product directly in the expanded view of preparation is carried out, so that the graph is very painting mold the big advantage, I have seen a lot of mold designers directly to expand FIG manual calculation preparation, this method is inefficient, draw a template size directly on the drawing to assemblage diagram form expression, a You can complete the preparation aspect, on the other hand save a lot of work in various parts of the mold work, because only join positioning pins, guide posts, screw holes can be drawn in the drawing in the preparation of the components work.

4. After the completion of preparation can be drawn fully into the mold figure, drawing in the preparation of a reconstituted out drawing of each component, such as adding screw holes, guide post holes, positioning holes and other holes, and the punching die threading hole wire cutting various holes required in the mold, the gap between the upper and lower molding die, must not forget that it is after the completion of a product of mold Figure has almost completed 80%, while in the process of mold drawing graph should pay attention: each step of the production means, such as bench marking, cutting lines until a different processing step has a complete production well layer, so that the line cutting and drawing management have great benefits, such as color distinctions like size the label is also a very important work, but also one of the most troublesome work because a waste of time.

5. After the above drawing is complete, in fact, we can not release drawings, the need for mold drawings proofing, all the accessories group sets up a different mold for each plate making different layers, and on the same basis as the guide pin hole until the mold Assembling analysis, and expanded view of each step product set into the group legislature figures, die gap and down to ensure that each template holes is consistent with the position and bend correctly.

Main Technique Parameters


718H, P20, NAK80, 2316, 2738, 2344

Product Material

ABS, PPR, PC, PP, PVC, POM, PMMA, PS, PE, PET, Rubber, Silicone, PA, PBT, PEI, etc.


LKM or by requested


Double color injection mould, Solid Mould, Insert Mould, Mould with Slide, Mould with Lifter

Runner System

Hot runner, Cold runner


Single cavity, multi cavities by requested (support similar products in one mould)


Corrosion word, Mirror finish, Brushed


Available SHOTS will depend on the steel material you choose

Mould standard

HASCO, DME, MISUMI, or by requested etc.


CAD, Pro-E, UG, etc

Design Time

3-7 days after we receive your samples or your drawings

Main Technique

Milling, Grinding, EDM, Wire-cutting, Engraving, CNC, etc.

Production time

1-3 months, depends on mould structure


Wooden case, or by request

The flow chart to place a mould order

Receive inquiries from customers

We will send you quotation within 24 hours after inquiries confirmed

Customers need to offer samples or 2D/3D drawings and some details about the mould

Confirm the order (quality , price , material , delivery time , payment terms etc.)

According to your requirement to prepare the production

Clients confirm the details of the mould

Surface shaping

Drill holes , high speed carve machine ,wire cutting , EDM, etc.

Arranging the test mould and sending the samples to customers

If customers do not satisfy the samples, please give us advice to repair

Repair , Polish , Texture

We will send samples to customers for confirming

Delivery by sea or by air ,etc


Below are just a few reasons to do business with yuesen:

- Sufficient experience in plastic mold design and manufacture

- Outstanding teamwork

- Constant technical innovation

- High-quality, low-cost, trouble-free molds

- Attentive after-sales services